Modulating heating operation includes - Modulating gas valve, inducer and circulating blower, Modulating operation from 100% to 35% input in 100 increments with nearly constant temperature rise
• Easily applied in upflow, horizontal left or right, or downflow installation with minimal conversion necessary
• Compact, easy to install, ideal height 33 Inch tall cabinet
• ECM variable speed drive for cooling SEER enhancement, improved comfort with optional airflow delay profiles and continuous fan options for IAQ performance
• Easy access to controls to connect power/control wiring
• Built-in, high level self diagnostics with fault code display
• Low unit amp requirement for easy replacement application
• All models are convertible to use propane (LP) gas
• Electronic Hot Surface Ignition saves fuel cost with increased dependability and reliability
• 100% shut off main gas valve for extra safety
• 24 Volt, 40 Volt Amp control transformer and blower relay supplied for add-on cooling
• Airflow leakage less than 1% of nominal airflow for duct performance testing conditions
• Solid removable bottom panel allows easy conversion
• Hi-tech tubular aluminized steel primary heat exchanger with stainless steel tube/aluminum fin secondary heat exchanger for outstanding efficiency
• No knockouts to deal with, making installation easier
• Movable duct connector flanges for application flexibility
• Quiet inducer operation, burner, and blower operation
• Inducer rotates for easy conversion of venting options
• Fully supported blower assembly for easy access and removal of blower
• External air filters used for maximum flexibility in meeting customers IAQ needs
• Insulated blower compartment for thermal and acoustic performance
• 1/4 turn knobs provided for easy independent door removal
• Internal condensate trap design (patent pending) provides condensate management options and is self priming to prevent nuisance problems
• These models may be connected as part of a communicating control system using a 4-wire connection bus
• AHRI Certified
• Energy Star® Rated
• Made in USA"" | • Gas Furnace • Type Variable Speed, Multi-Position • Btu per Hour 80 MBH (Input), 77 MBH (Output) • Capacity 1200 CFM • Control Type Thermostat • Size 17-1/2 Inch Width x 28-1/2 Inch Depth x 33 Inch Height • Inclusion/Features Modulating Gas Valve, Inducer and Circulating Blower, ECM Variable Speed Drive, Electronic Hot Surface Ignition, 24 Volt 40 Volt Amp Control Transformer, Hi-Tech Tubular Aluminized Steel Primary Heat Exchanger, Solid Removable Bottom Panel, External Air Filter, Self Priming Internal Condensate Trap • AFUE Efficiency 97.5 Percent • Current Rating 7.5 Amp • Temperature Rating 40 to 70 Deg F (Air Rise), 190 Deg F (Maximum Outlet) • Blower Motor Rating 1/2 HP, 4.8 Amp • Blower Size 11 Inch x 8 Inch • Applicable Standard CSA, AHRI, ISO 9001 | • AFUE Efficiency 97.5 Percent • Current Rating 7.5 Amp • Temperature Rating 40 to 70 Deg F (Air Rise), 190 Deg F (Maximum Outlet) • Blower Motor Rating 1/2 HP, 4.8 Amp • Blower Size 11 Inch x 8 Inch • Applicable Standard CSA, AHRI, ISO 9001 | • These compact units employ induced combustion, reliable hot surface ignition and high heat transfer aluminized tubular heat exchangers. The units are factory shipped for installation in upflow or horizontal applications and may be converted for downflow applications. These furnaces are designed for residential installation in a basement, closet, alcove, attic, recreation room or garage and are also ideal for commercial applications. All units are factory assembled, wired and tested to assure safe dependable and economical installation and operation. These units are Category IV, National Fuel Gas Code and may be vented either through side wall or roof applications using approved plastic combustion air and vent piping. Approved plastic combustion air and vent piping include Selkirk Polyflue, Duravent Polypro, & Centrotherm Innoflue polypropylene venting systems. | Acclimate™ Series |