Easily applied in upflow, horizontal left or right, or downflow installation with minimal conversion necessary
• Compact, easy to install, ideal height 33 Inch tall cabinet
• Blower-off delay for cooling SEER improvement
• Easy access to controls to connect power/control wiring
• Built-in, high level self diagnostics with fault code displays standard on integrated control module for reliable operation
• Low unit amp requirement for easy replacement application
• All models are convertible to use propane (LP) gas
• Electronic Hot Surface Ignition saves fuel cost with increased dependability and reliability
• 100% shut off main gas valve for extra safety
• 5 speed, direct drive Standard ECM style high efficiency DC motor
• 24 Volt, 40 Volt Amp control transformer and blower relay supplied for add-on cooling
• Hi-tech tubular aluminized steel primary heat exchanger
• Secondary heat exchanger made of corrosion resistant stainless steel materials
• Timed on, adjustable off blower capability for maximum comfort
• Blower door safety switch
• Solid removable bottom panel allows easy conversion
• Airflow leakage less than 1% of nominal airflow at duct performance testing conditions
• No knockouts to deal with, making installation easier
• Movable duct connector flanges for application flexibility
• Quiet inducer operation
• Inducer rotates for easy conversion of venting options
• Fully supported blower assembly for easy access and removal of blower
• External air filters used for maximum flexibility in meeting customers IAQ needs
• Protection included from air intake, exhaust vent, or condensate blockage
• Patent pending self priming internal condensate trap design for easy installation
• Venting applications - may be installed as a either 2-pipe(sealed combustion) or single-pipe vent (using indoor com-bustion air)
• No special vent termination required
• 1/4 turn knobs provided for easy door removal
• High-efficiency blower motor for lower electrical power usage and improved A/C SEER ratings
• Insulated blower compartment for terminal and acoustic performance
• AHRI Certified
• Energy Star® Rated
• Made in USA"" | • Gas Furnace
• Type Standard, 1-Stage, Multi-Position
• Btu per Hour 95 MBH
• Capacity 2000 CFM
• Control Type Thermostat
• Size 21 Inch Width x 28-1/2 Inch Depth x 33 Inch Height
• Gas Inlet Size 1/2 Inch
• Inclusion/Features Electronic Hot Surface Ignition, Direct Drive Standard ECM, 24 Volt 40 Volt Amp Control Transformer, Hi-Tech Tubular Aluminized Steel Primary Heat Exchanger, Blower Door Safety Switch, Solid Removable Bottom Panel, External Air Filter, Self Priming Internal Condensate Trap
• AFUE Efficiency 95 Percent
• Current Rating 12.2 Amp
• Temperature Rating 35 to 65 Deg F (Air Rise), 190 Deg F (Maximum Outlet)
• Blower Motor Rating 3/4 HP, 8.4 Amp
• Blower Size 11 Inch x 11 Inch
• Applicable Standard CSA, AHRI, ISO 9001 | • AFUE Efficiency 95 Percent
• Current Rating 12.2 Amp
• Temperature Rating 35 to 65 Deg F (Air Rise), 190 Deg F (Maximum Outlet)
• Blower Motor Rating 3/4 HP, 8.4 Amp
• Blower Size 11 Inch x 11 Inch
• Applicable Standard CSA, AHRI, ISO 9001 | • These compact units employ induced combustion, reliable hot surface ignition and high heat transfer aluminized tubular heat exchangers. The units are factory shipped for installation in upflow or horizontal applications and may be converted for downflow applications. These furnaces are designed for residential installation in a basement, closet, alcove, attic, recreation room or garage and are also ideal for commercial applications. All units are factory assembled, wired and tested to assure safe dependable and economical installation and operation. These units are Category IV, National Fuel Gas Code and may be vented either through side wall or roof applications using approved plastic combustion air and vent piping. Approved plastic combustion air and vent piping include Selkirk Polyflue, Duravent Polypro, & Centrotherm Innoflue polypropylene venting systems. |
