YH-10C00ATAAA1 Model 10 Ton - 120,000 BTU/Hour, 208/230 VAC 60 Hz 3-Phase, 41.4 A MCA, 11.2 EER, 9800 CFM, R-410A, Tandem Scroll Compressor, Split System, Condenser, Standard Efficiency, Air Conditioner Outdoor Unit
Product Description
More Information
EASY TO INSTALL - Split system air conditioner weighs much less than a packaged unit of similar capacity for easier rigging • Completely assembled, piped and wired at the factory to provide 1-piece shipment and rigging • Smart Equipment simplifies setup and commissioning • Factory-installed disconnects, convenience outlet and TechniCoat coil option • A filter-drier is shipped in the unit’s control box for field installation in the liquid line. Copper stub-outs are factory mounted on the suction and liquid lines to simplify the field piping connections • Compressor staging (above 7.5 tons) for capacity reduction provides more economical operation and even temperature levels within the conditioned space • FLEXIBILITY - Meets EPACT 2005 and exceeds ASHRAE 90.1 efficiency standards • 2-pipe (YH) and 4-pipe (YJ) configurations available for on-site flexibility • Standard operation to 40 Deg F. Factory- or field-installed Low Ambient VFD control to 0 Deg F • Solid state or internal line break compressor motor protection • Networkable to send all alarms and diagnostic data directly to an on-site PC if desired • DURABILITY - Feel confident with built-in protections and certified safeties • Five-minute anti-short cycle timer and minimum compressor run time • Durable finish made of pre-painted, galvanized steel meets 1000-hour salt-spray test demands • Proven scroll compressors provide both high efficiency and reliability • Condenser coils are constructed of MicroChannel aluminum tubing and aluminum fins for durability and long-lasting efficient operation • AHRI Certified • Energy Star® Rated""
• Air Conditioner Outdoor Unit • Type Split System, Condenser, Standard Efficiency, 2-Pipe • Voltage Rating 208/230 Volt AC • Current Rating 41.4 Amp (MCA), 50 Amp (Maximum Fuse Breaker), 15.7 Amp Rated Load/110 Amp Locked Rotor (Compressor), 3 Amp Full Load (Fan Motor) • Frequency Rating 60 Hertz • Number of Phases 3 • Power Rating 3/4 HP (Motor) • Cooling Capacity 10 Ton • Temperature Control Type Thermostat • Enclosure Material Galvanized Steel • Enclosure Finish Zinc Coated • Size 59.1 Inch Length x 31.9 Inch Width x 50 Inch Height • Weight 497 Pound • Approval CSA (Canada and US) • Compressor Type Tandem Scroll • Refrigerant Type R-410A • Air Flow Rating 9800 CFM • Energy Efficiency Ratio 11.2 EER • Refrigerant Line Size 1-3/8 Inch (Suction), 7/8 Inch (Liquid) • Application Commercial • Application Commercial • Applicable Standard AHRI, ASHRAE 90.1, ISO 9001
• Delivering heating and cooling equipment you can trust requires an uncompromising approach to quality. Through innovative processes and rigorous testing, each Luxaire unit is built to provide consistently dependable comfort. Ducted Systems condensing units and heat pumps are completely assembled, piped and wired at the factory to provide a single-piece unit for shipment and rigging. Each unit is pressurized with a holding charge of refrigerant R-410A for storage and/or shipping. The compact design, clean styling, small footprint, and quiet operation make these condensing units and heat pumps suitable for almost any outdoor location. On rooftops... because they weigh much less than a single package unit of similar capacity and are much easier to rig and support. On the ground... because the footprint is compact allowing a variety of applications. Both the Ducted Systems condensing units and heat pumps are equipped with reliable Smart Equipment™ microprocessor controls to assure proper operation and unit protection for long product life. Products from 10 to 20 tons are available in single or dual (2 or 4 pipe) refrigerant circuits for redundancy in operation and various applications. The Ducted Systems air handling units are completely assembled units, including a well-insulated cabinet, a DX cooling coil with copper tubing, aluminum fins, expansion valve(s), distributor(s), 2” throwaway filters, a centrifugal blower, a blower motor, an adjustable belt drive, a blower motor contactor and a small holding charge of nitrogen. Units are shipped in the vertical position ready for field installation, but can be easily converted to horizontal position. An added benefit of the Ducted Systems air handling units is they are designed to operate with either a condensing unit or a heat pump and no field modification or special unit is required for heat pump applications.
Optimum™ Pro Series
Specifications
Specifications
Cooling Capacity
120000 BTU/Hour
Individual Item Weight
497.000 Pound
Manufacturer
Johnson Controls (Luxaire Heating & Air Conditioning)
